On the 2018 Alfa Romeo Stelvio, faults with the windscreen wipers and tailgate deserve extra attention. Does a wiper now only work at low speed? Then it is not automatically worn out. Won’t the tailgate open? That does not mean the drive unit has to be replaced straight away. Water, switches and adjustment can all play a role. The motor control system can also intervene. That is the electronics that control and monitor the wiper motor. Anyone who distinguishes the symptoms properly can avoid unnecessary repairs.
Known wiper problems with the 2018 Alfa Romeo Stelvio
On certain 2018 Stelvios, the wiper control can incorrectly determine that the motor is overheating. The control then limits the wipers to low speed. According to the recall for this model year, operation at higher settings may therefore fail. That reduces visibility, especially in heavy rain.
Do not only check whether the wipers move. Also test the intermittent setting and both continuous speeds. Pay attention to whether the operation changes after longer use. On the page about Alfa Romeo Stelvio problems you will find more points to look out for with this model. If a wiper setting does not work properly, have the vehicle identification number checked to see whether a recall applies to your car.
Is the wiper motor faulty?
A wiper that only turns slowly is not necessarily suffering from a mechanical fault. That would mean the motor itself is physically damaged or seizing. In the 2018 fault mentioned above, it is the motor control that intervenes. The recall provided for inspection and, depending on the result, replacement of the motor. Without a diagnosis, replacing it may leave the real cause untouched.
Do the wipers move without being switched on? Or do they fail at the same time as other electrical functions? Note when this happens, for example after rain. For the 2018 Stelvio, recalls were also recorded concerning water ingress at the body control module. This control unit manages various electrical functions. Among other things, the wipers, exterior lighting, indicators and horn may be involved. A wiper moving on its own does not by itself prove that this module is defective.
Ask the workshop to investigate the cause step by step:
- Read out fault codes. These are stored fault messages from all the systems involved, not just the wiper control.
- Check connectors, power supply and earth connections for moisture or corrosion.
- Look for where the water is getting in by checking for signs of moisture.
- Check the recall status and, after the repair, test all wiper settings again.
Do the wipers still stick on low speed? Have the cause assessed before you continue driving in bad weather.
Streaking and noise call for a different check
Do the wipers judder or squeak? Or do they leave streaks? That does not immediately point to an electronic problem. In a technical service bulletin from Stellantis, dirt on the wiper rubber is listed as a first check point. Such a bulletin is technical guidance for workshops. Clean the windscreen and wipe the rubber with a damp, lint-free cloth. Then check whether the rubber has cracks and whether the wiper arm presses down evenly.
If the wipe pattern is still poor after cleaning, new blades are the logical next step. New wiper blades will not fix a failed high-speed setting. Investigate streaking and speed problems separately.
Tailgate won’t open on the Stelvio: where is the fault?
A tailgate that will not open or close can have several causes. First test all operating points: the key, the button inside the cabin and the button on the tailgate itself. If only one button does not work, have that switch and the wiring checked. If none of the buttons work, also have the power supply, stored fault messages and locking checked.
With every attempt, pay attention to what the tailgate does. Does the lock release but the tailgate does not move? Or does the tailgate begin to move and then stop halfway? That information helps the workshop search more precisely. It prevents the switch, lock and drive unit being replaced unnecessarily at the same time.
Close button does not work after rain
For certain 2018 Stelvios, a recall has been recorded because water may enter the connector connections and the tailgate switch. Corrosion can disrupt operation and can even cause an unintended opening signal. Does the problem occur mainly after rain or a wash? Tell the workshop. The time at which the fault occurs helps to identify the cause.
You can check these points yourself:
- Moisture or deposits around the push buttons and beneath the tailgate trim.
- Cracks or loose sections at the rubber cable grommets.
- Water collecting inside the tailgate after a wash.
- A warning on the instrument panel that the tailgate is not locked.
Have the connectors and wiring checked before replacing a complete drive unit. If the tailgate does not close reliably or opens unexpectedly, do not use the car as normal. Have the lock and controls checked first.
Tailgate drops back down or only closes after several attempts
If the electric tailgate reaches the highest position but then drops back down slightly, a weak gas strut may be involved. Check whether the left and right sides move evenly. Also note whether the problem is worse in cold weather. Have a damaged or greasy gas strut inspected by a specialist. Do not remove a gas strut yourself while the heavy tailgate is open.
The adjustment of the lock and tailgate can also hinder electric closing. An uneven gap, a hard click or a tailgate hanging crookedly indicates resistance when locking. Have the striker plate and hinges checked before replacing the closing motor. An adjustment must not disguise damage to a hinge or the bodywork.

Targeted checks prevent unnecessary parts replacement
On a used 2018 Stelvio, test all wiper settings and tailgate buttons. Open and close the tailgate several times. Check the gaps and ask for proof of any recall work carried out. Are there signs of moisture or changing electrical faults? Then have a diagnostic test carried out as well. That gives you a better view of the cause: contamination, adjustment, water or a faulty component.
Read more on Carnews about Stelvio problems, maintenance and tracking down faults. That way you can find out which checks are right for your car.
Frequently asked questions
The main technical cause is incorrect software in the wiper motor, which falsely detects overheating and restricts the wipers to low speed. In addition, water ingress at connectors or the body control module can cause faults in power supply, earth and control. Wipers that rattle, jump or leave streaks are often caused by dirty, hardened or worn wiper blades or a contaminated windscreen. 2018 Stelvios in particular are prone to these problems.
The Stelvio’s electronic architecture links the electric tailgate to the central vehicle control system via switches, sensors, wiring and the body control module. As a result, moisture, corrosion or poor connectors—especially on 2018 models—can cause incorrect signals, meaning the tailgate does not respond, closes poorly or opens unexpectedly. Not every fault is electronic: dropping back down, heavy closing or a crooked position point more to gas struts, the drive unit or adjustment. That is why fault codes, software, recall status and wiring must be checked before parts are replaced.
Regularly check the recall status and have any open campaigns carried out, especially on a 2018 Stelvio. Keep the windscreen, wiper rubbers, seals and drain openings clean and dry, and inspect switches, cable grommets and connectors for moisture or corrosion. Test all wiper settings and the tailgate operation periodically, and have abnormalities such as dropping back down, crooked alignment or unexpected opening investigated professionally without delay.
Using suitable diagnostic equipment, first read out all fault codes, including those from modules other than the wiper control. Then check the body computer, connectors, power supply and earth for moisture, oxidation or damage and deal with the cause first. After that, clear the fault codes with the diagnostic tester and carry out a new system test in which all wiper settings are checked. It is preferable for this to be done by an Alfa Romeo specialist, and open recalls should also be checked.
In the tailgate module, the close button/switch and connectors are the parts that most often fail due to moisture and corrosion; the right gas strut also commonly fails. First check the plugs, cable grommets and seals, clean off light corrosion and replace a faulty switch by removing the interior trim, disconnecting the plug and fitting and sealing a new switch. A gas strut should only be replaced with the tailgate properly supported, after which you release the retaining clips and click the new gas strut onto the ball joints. Have damaged wiring, electric drives or a tailgate that does not close reliably repaired by a specialist.





