A rattling suspension on a Volvo S40 often points to play in the front suspension, with anti-roll bar links and control arm bushes as well-known trouble spots. Squeaking, creaking in corners and a dull thud over speed bumps help to narrow down the cause. If you assess the noise properly, you can prevent a small defect from developing into erratic steering behaviour or extra tyre wear. Read on and tackle the diagnosis step by step.
What causes a rattling suspension on a Volvo S40?
In the Volvo S40, a rattling or clunking noise usually comes from the front axle. The cause is not always a single part. Especially on older cars, bushes, ball joints and strut components can all show wear at the same time. According to the technical diagnostic information for this issue, anti-roll bar links, anti-roll bar bushes, control arm bushes and strut top mounts are the first parts worth checking.
The type of noise often gives clues. A sharp rattle over cobbles or short ridges is more often associated with an anti-roll bar link with play. A dull knock when braking, accelerating or lifting off the throttle is more likely to be caused by a control arm bush that no longer holds the control arm firmly in place. Creaking noises when turning the steering wheel more often point to a strut bearing or the upper spring seat.
The following signs help to tell the difference:
- A light metallic tapping over small bumps often points to an anti-roll bar link or anti-roll bar bush.
- A heavy bang over a speed bump can come from a broken spring, strut bearing, spring seat or shock absorber.
- A knock when braking or pulling away may be caused by movement in the control arm bushes or a ball joint.
- Squeaking or creaking in a bend can happen because a spring is not rotating smoothly in the strut.
- A car that changes direction under braking should be checked for control arm bushes, ball joints and wheel alignment.
‘ A nut that is not properly tightened can produce the same noise as a worn joint. ’
Anti-roll bar links often cause rattling
The anti-roll bar reduces body roll in bends. At both ends, short drop links connect the anti-roll bar to the suspension. These links contain ball joints with dust boots. If such a boot splits, dirt can get in and play develops.
You will notice that play especially on setts, ridges and poor-quality tarmac. The noise is often clearer when one wheel hits a bump. Driving over a speed bump at an angle is therefore a useful test: the anti-roll bar is then loaded unevenly. A noise that becomes louder in this way makes the drop link or rubber bush suspicious.
Also check the securing nuts. A nut that is not properly tightened can produce the same noise as a worn joint. For inspection, it is best to raise both front wheels at the same time. If only one side is hanging free, the anti-roll bar is under tension and play is harder to feel.
Checking the anti-roll bar bushes on the Volvo S40
The anti-roll bar is attached to the subframe with rubber bushes and metal brackets. Over time, these bushes can dry out, shrink or split. The bar then gets room to move and can knock against the subframe or a control arm. This usually causes a dull tap, sometimes accompanied by squeaking at low speed.
Check whether the brackets are still straight and whether the bar sits centrally in the bushes. Also look for bright metal marks around the bar and the subframe. Such marks can show that parts are touching. Always replace damaged bushes with items that match the version and diameter of the anti-roll bar.

Control arm bushes give a knock under load
A control arm connects the suspension to the subframe. The rubber bushes in the control arm absorb movement while keeping the wheel geometry within the intended limits. If a control arm bush splits or comes away from the metal sleeve, the control arm can visibly shift under braking and acceleration.
On a Volvo S40, you may notice this not only through noise. The steering can feel more unsettled on tramlines. The car may also pull left or right under heavy braking. Uneven wear on the inside or outside of the front tyres is another clue, although that can have other causes too.
A visual inspection alone is not enough. A bush may still look acceptable on the outside while moving too much under load. A garage checks this on a lift using the correct lever. They will look for splits in the rubber, whether the metal core shifts and whether the control arm contacts nearby parts.
How do you replace control arms in a Volvo S40?
Replacing a control arm is perfectly doable for an experienced home mechanic with decent tools, but it is not a job for a car supported only by a jack. The ball joint, subframe mountings and wheel alignment are all involved. The exact bolts, fitting method and parts differ between the first S40 generation from around 1995 to 2004 and the second generation from around 2004 to 2012.
The process broadly consists of the following steps:
- Park the car on level ground, secure the rear wheels and place the front end on axle stands.
- Remove the front wheel and first inspect the brake hose, ABS cable, ball joint and mountings.
- Release the connection between the control arm and the ball joint according to the instructions for your version.
- Remove the control arm bush bolts from the subframe and take the control arm out.
- Carefully compare the new control arm with the old part, including the position of the bushes and ball joint.
- Fit the new control arm with new self-locking nuts where the manufacturer requires them.
- Only fully tighten the rubber bushes once the suspension is at normal ride height.
- After fitting, have the wheel alignment checked.
That tightening at ride height is important. If the rubber bushes are tightened while the suspension is hanging fully extended, they will already be twisted once the car is back on its wheels. This shortens the life of the rubber and can cause creaking again. If in doubt, having the job done by a garage is wiser, especially if corrosion around the mountings makes dismantling difficult.
‘ A slight rattle may seem harmless, but without inspection that cannot be confirmed reliably. ’
Rule out strut top mounts and broken springs
Not every rattling suspension on a Volvo S40 is caused by control arms or anti-roll bar links. The upper strut mount, strut bearing and front spring also deserve attention. With a faulty strut bearing, the spring turns less smoothly when steering. This can cause creaking, a noticeable click through the steering wheel or a dull knock at low speed.
A broken end of the front spring is especially important to rule out on older S40s. The broken section often sits at the bottom of the spring seat and is not always immediately visible. Check whether the car sits lower on one side, whether the spring is seated correctly and whether there are metal marks around the strut. Replace a broken spring on both sides of the axle and have the spring seats checked as well.
Do not keep driving if a wheel is visibly out of line, the steering feels loose or metal is striking metal. A broken spring, clear play in a ball joint or contact between the tyre and wheel arch liner also calls for immediate repair. A slight rattle may seem harmless, but without inspection that cannot be confirmed reliably.

What does it cost to repair a rattling suspension?
The repair costs depend entirely on the fault, the generation of the S40, the parts chosen and the labour required. Replacing a drop link usually takes less work than replacing a control arm or complete strut. With a strut, the spring must be safely compressed and removed, which increases labour time.
Ask for a breakdown of parts, labour, wheel alignment and any additional work. If control arm bushes, ball joints and anti-roll bar links all show wear, combined replacement can save labour hours. However, only have parts replaced if inspection shows clear play, damage or ageing.
After the repair, check during a test drive whether the noise over setts, speed bumps and when steering slowly has gone. Also pay attention to straight-line driving, steering self-centring and tyre noise. On the Carnews website you will find much more information about Volvo problems, suspension noises, maintenance and targeted diagnostics. Discover more on Carnews before you order parts or book a repair.
Frequently asked questions
On the Volvo S40, the control arm bushes can split or deform too much under load, causing a dull knock when braking or accelerating, changes in direction and uneven tyre wear. The anti-roll bar links often develop play in their ball joints or at the securing nuts, which causes a sharp rattle, especially over small bumps. The anti-roll bar bushes can also dry out, shrink or split, allowing the bar to knock against the control arm or subframe.
Worn top mounts mainly give a dull thud over speed bumps and a click or creak when steering at low speed; sometimes the spring turns jerkily. Play in track rod ends appears more as rattling over uneven surfaces, a vague or delayed steering feel and changes in direction during quick lane changes. Confirm this while stationary: feel at the top of the strut while steering and check the track rod ends by moving the wheel back and forth at 3 and 9 o’clock.
You cannot safely dismantle a McPherson strut completely without a suitable spring compressor; never undo the central piston rod nut while the spring has not been properly compressed. Put the S40 on axle stands, remove the wheel, anti-roll bar link, brake hose/ABS mountings and the lower and upper strut bolts, while supporting the hub carrier. If necessary, have a garage transfer the spring, preferably fit new bearings, mounts, dust covers and bump stops, and replace springs in pairs across the axle. Use new specified locking nuts, tighten everything to the specifications for the model year and version, and then have the wheel alignment checked.










