A faulty indicator on the Honda FR-V sometimes points to a relay fault in module 38650-SJD-E01. First check the bulbs, bulb holders and wiring. Is it only the left indicator that does not work, or does a bulb stay on instead? Then compare the operation of the indicators with that of the hazard warning lights. This will stop you replacing the entire fuse box when a targeted repair is enough.
Why doesn’t the Honda FR-V left indicator work?
On the Honda FR-V, a faulty relay in the interior fuse box sometimes disables one indicator. Reported repair cases for this model show that the relay on the circuit board can fail, while the other direction still works. Do not immediately blame the module: a bulb, socket or earth connection can produce the same fault symptoms.
First look at exactly what is happening. Switch on the left indicator and then test the hazard warning lights. Walk around the car. Check the indicators at the front and rear and, if fitted, on the side. Compare left with right.
These differences help with the initial diagnosis:
- If one bulb does not flash and the others flash faster, check that bulb, the holder and the contacts.
- If the entire left side does not work, even with the hazard warning lights, investigate the power supply, wiring and relay control for that side.
- If the hazard warning lights on the left work but the indicator does not, check the steering column switch and the individual control circuit.
- If neither side works, start with the fuses and the fuse box power supply.
A fast flashing rate does not automatically mean the relay is faulty. A bulb with poor contact also changes the circuit load. Check that first before dismantling the fuse box.
‘Otherwise a new relay will be damaged again.’
Relay problems in module 38650-SJD-E01
In some FR-V faults, the cause lies with the relay in module 38650-SJD-E01. If the relay is demonstrably faulty, replacing it restores the indicator function. Do not pull a loose relay out of the fuse box at random. If the fault is on the circuit board, soldering work is required.
Before repairing it, check the part number on the unit in your car. Then compare the connector layouts with those of the replacement part. The specification and electrical equipment vary by car. The correct part number is especially important for a used unit or a replacement relay with the same specifications.
The interior fuse box is located under the steering wheel, on the right-hand side of the driver’s area. Also inspect the rest of the fuse box. Discolouration, melted plastic and damaged solder joints point to heat build-up. Have the cause investigated. Otherwise a new relay will be damaged again.
How to investigate a faulty indicator step by step
Start with the bulbs and then check the control signal. This avoids unnecessary dismantling and lets you link test results to the fault symptoms. Follow these steps:
Check the bulbs with the hazard warning lights switched on. Look for black deposits, a damaged filament and moisture in the lamp unit. Replace a faulty bulb with the specified type and wattage.
Inspect the holder and contact points. Corrosion or a contact that does not grip firmly sometimes causes an interruption. Also check whether the bulb works again from time to time if you gently move the connector.
Check the fuses using the diagram on the cover or in the owner’s manual. Ideally, test them with a multimeter. Only fit a fuse with the same amperage. If it blows again, inspect the circuit for a short circuit.
Investigate the earth and wiring on the failed side. A poor earth sometimes causes dim lighting or irregular flashing. If necessary, measure the voltage drop between the holder earth and the negative battery terminal while the bulb is switched on.
Check the steering column switch and the relay module if the bulbs and connections are in good order. Does the indicator work again if you move the lever gently? Then inspect the switch. If one direction keeps failing, investigate the relay circuit in the fuse box.
During diagnosis, note the result of each test. In particular, compare the indicators with the hazard warning lights. This will show whether the bulbs on the failed side still work when operated in a different way.
The indicator stays on on the Honda FR-V
An indicator that stays on continuously without flashing calls for a different check from a bulb that does not light at all. A stuck or internally damaged flasher relay is then a clear suspect. First establish whether it affects one bulb, one side or the whole indicator function. Also check the bulb and contacts: an incorrect bulb or poor contact affects the flashing behaviour.
Switch the indicator off and test the hazard warning lights. See whether the light stays on with both controls and listen for the relay switching. Do not rely on a clicking sound alone: a relay can click while the electrical contact is not working properly. So measure the control signal and output before replacing a part.
Does the indicator keep burning while the lever is in the neutral position? Then have the steering column switch and the module checked. This prevents replacing the relay while the fault lies in the switch or wiring.
‘Leave circuit board work, such as removing and resoldering a relay, to someone with experience in automotive electronics.’
Replace the relay or repair the fuse box?
If the relay in module 38650-SJD-E01 is demonstrably faulty, a targeted relay replacement is sometimes enough. According to reported FR-V repair cases, replacing the entire fuse box is not always necessary. The condition of the circuit board, solder joints, connectors and housing determines which repair is appropriate.
Disconnect the battery before removing the fuse box. Take photos of the connector positions. Check the connections for signs of heat. Leave circuit board work, such as removing and resoldering a relay, to someone with experience in automotive electronics. A relay with different specifications is not a suitable replacement.
Is the circuit board charred or the connector housing melted? Then a new relay alone is not always enough. Have the damage assessed. When replacing the unit, compare the part number and the connectors. After the repair, test both indicators and the hazard warning lights. Also check the other lights for loose connections.
Want to know more about faults and maintenance for this model? On the Carnews website you will find information about the Honda FR-V and related car problems. Read which checks you can do yourself and when specialist diagnosis makes sense.
Frequently asked questions
The most common causes are a blown bulb, a corroded or loose holder, a poor earth connection and a faulty fuse. Damaged wiring or a worn steering column switch can also cause the fault. A specific point to note on the Honda FR-V is a faulty or burnt relay on the circuit board of the interior fuse box.
On the Honda FR‑V, first switch on the hazard warning lights: if they work on both sides, the bulbs, earth and wiring are probably fine and the steering column switch is suspect. Move the indicator lever; if the indicator temporarily comes back, the switch is probably worn or the connector is poor. If one side also does not work with the hazard lights, first check the bulbs, holders and earth; if those are fine, the integrated relay on the interior fuse box circuit board is probably faulty.
First test the fuses for the indicators and hazard warning lights, as shown on the fuse box cover or in the owner’s manual. Check them with a multimeter; a visual inspection alone is not enough.
A replacement automotive circuit board relay or a relay module with exactly the same specifications as the original offers a reliable solution. If the circuit board itself is damaged, a professionally refurbished interior fuse box with an identical part number can be fitted. Universal relays or units with different specifications are not recommended.







