Camshaft adjuster seals and engine oil leaks call for careful diagnosis, because a worn seal is not always the only cause. Crankcase pressure, wear in the camshaft adjuster and incorrect installation can also cause oil leakage. Simply replacing the seal then offers no lasting solution. Read what to look out for before oil reaches surrounding engine components.
What is a camshaft adjuster?
A camshaft adjuster changes the timing at which the inlet valves or exhaust valves open and close. This system is also known as variable valve timing, or VVT. On certain Volvo V70 engines, the adjuster is on the timing side of the cylinder head.
The engine management system controls the camshaft adjuster with oil pressure. This allows the engine to adjust valve timing to engine speed and load. That supports smooth power delivery, refined engine running and efficient fuel consumption. For proper operation, the adjuster, oil passages and seals must all be in good condition.
There are seals, oil seals and sometimes blanking plugs around the camshaft. These parts keep engine oil inside the cylinder head. As soon as a seal hardens, becomes damaged or does not sit properly in its seat, oil can escape.
How do leaks occur at the camshaft adjustment?
Wear caused by age and temperature is a well-known cause. Rubber loses its flexibility over time, while the seal is continually exposed to hot engine oil. A small leak can then spread over the timing cover and down the engine block. That can make it seem as though the oil is coming from several places.
However, a leaking seal is not always the whole problem. Common causes around the camshaft adjustment include:
- a hardened or damaged camshaft oil seal;
- play or wear in the VVT unit;
- a loose mounting of the camshaft adjuster;
- excessive crankcase pressure due to a blocked crankcase ventilation system;
- a seal fitted crookedly or too deeply;
- leakage at a blanking plug or valve cover gasket.
The positive crankcase ventilation (PCV) system carries gases and pressure out of the crankcase. If this system becomes blocked, pressure finds a way out along weak seals. As a result, a new oil seal can start leaking again. So do not just deal with the visible leak; have the crankcase ventilation checked as well.
How do you recognise a leaking seal?
An oil leak around the camshaft adjuster often starts small. You may see a greasy edge at the cylinder head or timing cover. Drips under the car usually only appear once the leak has developed further. So also check for light oil traces during servicing.
Pay particular attention to the following signs:
- fresh oil around the camshaft sprocket or VVT unit;
- oil at the top of the timing side;
- a falling oil level without any obvious smoke;
- oil droplets under the engine after parking;
- an oil smell when oil reaches hot components;
- a seal leaking again after previous repair.
A wet underside of the engine block does not prove the leak starts there. Oil runs downwards by gravity and airflow. Other possible leak points are the crankshaft seal, the oil pump seal, the turbo oil lines and the sump. The highest point where fresh oil is visible often gives the best clue.
This is how the engine leak is carefully identified
Targeted diagnosis prevents unnecessary parts from being replaced. For this, the engine must first be clean. On a dirty engine block, old oil is difficult to distinguish from an active leak.
A workshop can carry out the following steps:
- Clean the timing side and the surrounding parts of the engine block.
- Check the oil level and note how much oil may be missing.
- Start the engine and then take a test drive.
- Look for the first fresh oil trace at the cylinder head.
- Check the camshaft oil seal, VVT unit and blanking plugs.
- Measure or check the operation of the PCV system.
- See whether previous seals have been fitted straight and at the correct depth.
After the repair, the same checks should be carried out again. A dry engine after a test drive makes it easier to see whether the leak has really been fixed. If oil still appears, the adjacent seals must also be checked.
‘ Regular checks are more sensible than replacing parts based on mileage alone. ’
How long do seals last?
There is no fixed replacement interval for a camshaft seal. Service life depends on age, mileage, engine temperature, the oil used and crankcase pressure. Long periods of inactivity can also cause rubber to age. So a seal can leak before any set maintenance interval has been reached.
Regular checks are more sensible than replacement based on mileage alone. Have the timing side inspected during an oil service or when work is carried out on the timing belt. Early oil traces are then often visible before drips appear under the car.
After replacement, the seal should remain tight for a long time. If the leak returns quickly, there may be overpressure, wear in the VVT unit or an installation error. Simply fitting the same seal again does not address the cause.

What does it cost to replace the seal?
The price varies by engine, version and accessibility of the parts. In some cases, a single seal can be replaced, but on other engines timing components and camshaft sprockets must be removed. The labour time therefore often makes up a large part of the bill.
The cause found also affects the cost. A worn VVT unit, contaminated PCV system or leaking blanking plug requires extra parts and work. So ask the garage for an itemised quote with parts, labour hours and additional checks.
If the timing belt has to be removed anyway and it is nearing its replacement interval, discuss which tasks can be combined. That avoids having to strip the same part of the engine again shortly afterwards. However, only have parts replaced where there is a technical reason to do so.
Why matching parts matter
The size and shape of an oil seal determine how it seals in the cylinder head. So use genuine parts or parts that demonstrably meet the same factory specifications. An incorrectly fitting seal can sit crookedly or fail to apply enough pressure to the camshaft.
Correct installation is just as important. The sealing surface must be clean and undamaged, while the seal is fitted straight and to the specified depth. The VVT unit must be fitted and secured according to the correct procedure. If in doubt, specialist knowledge of the engine type in question is advisable.
‘ Oil can damage rubber parts and trap dirt. ’
Is this important engine maintenance?
A small oil sweat spot does not always require immediate dismantling, but it does need checking. Oil can damage rubber parts and trap dirt. If the leak reaches the timing belt, a garage must assess the condition of the belt and surrounding components.
If you suspect a leak, check the oil level regularly and do not wait for a warning light to come on. Have the source identified before driving long distances or losing a lot of oil. With a clean engine, a check of the crankcase ventilation and suitable seals, the problem can usually be tackled in a targeted way.
On the Carnews website you will find much more information about engine problems, maintenance, known model faults and practical checks for car enthusiasts. Discover the related articles and learn how to recognise complaints earlier and have them investigated more precisely.
Frequently asked questions
The main symptoms are oil traces around the camshaft adjuster and oil running down the engine on the timing side. Oil can also end up on or behind the timing cover, making it look as though there are several leak points. A recurring leak after replacement may indicate crankcase overpressure or play in the VVT hub.
Set the engine to the specified TDC, mark the timing position and lock the crankshaft and camshafts with the correct special tools before removing the belt and VVT unit. Replace the seal or oil seal straight, at the specified depth and without damaging the sealing surface; at the same time, check the VVT hub for play and the PCV system for overpressure. Reassemble everything according to the engine-specific workshop manual and tightening torques, without turning the crankshaft and camshafts separately. Then turn the engine over by hand for two full revolutions, recheck the timing and only start it if nothing binds.
A leaking valve cover gasket lets oil escape along the edge between the valve cover and the cylinder head, usually on top of the engine. A leak at the camshaft adjuster occurs at the camshaft seal or VVT unit and often runs down the timing side. Besides a worn seal, this can also be caused by play in the VVT hub or overpressure due to a blocked PCV system. Cleaning and checking where the oil appears first determines the true source.

























